Wuqi Zhijian · Heran Amazement: New Product Guanfudun Qu Makes its debut with scinique® 2.0 Dual-protection Synergistic optical technology. Internal guarding: circularized polarized light · narrowband phase matching calibration + external guarding: Magnetron sputtering AR· anti-glare coating, Woowhead is equipped with a professional optical inspection card to visualize the state of light

Air bubbles, lifted edges, and fingerprints in film application: Causes and Solutions of Common problems

2026-09-22|Product Information|Author: Woowhead Technical Team, Dongguan Runjia Technology Co., LTD

What does this article talk about?

Bubbles are divided into "dust bubbles" (with particles in the center) and "adhering bubbles" (which can be extruded). The lifted edges are mostly due to positioning deviations or incompatibility of the shells. Fingerprint residue: Check the state of the oleophobic layer - Complete processing procedure attached.

01. Two types of bubbles

Dust bubble: Particles can be seen in the center of the bubble, due to residual dust on the film surface or screen surface. Treatment: Remove it with a dust-removing tape (lift the corner of the film from the bubble position, and after the dust-removing tape adheres to the particles, re-attach it). Adhesive bubbles: Extrudable bubbles without particles can be eliminated by pushing them outward from the center with your fingertips.

Key points for prevention: Choose a dust-free room for film application and turn off fans and air conditioners. First, tear off one corner of the film and align it with the receiver/camera for positioning, then gradually release the release film.

02. The lifted edge and the opening are misaligned

Common causes of edge curling: The edge extends beyond the curved surface of the screen (curved film) during positioning, the protective case squeeges the edge of the film, and the edge is not fully pressed after bonding. Handling: Reposition; Change the shell or select a shell type compatible with the membrane; Press along the edge for 30 seconds to allow the adhesive layer to fully spread.

Most of the misalignment of the holes is due to the wrong model selection - Guanfudun makes molds by model. Please check the model before placing an order. The product page has a comparison table.

03. Fingerprints and Hydrophobic layers

The new film's fingerprint can be wiped clean immediately, thanks to the oleophobic layer (with a water droplet Angle of 115°). The increase in wiping resistance after several months of use is due to the natural wear of the coating. Judgment method: If water drops into beads and rolls smoothly, it = the coating is healthy. The water droplets spread out = obvious wear of the coating.

In case of failed film application (dust bubbles cannot be removed, severe misalignment), Woowhead offers a replacement service for failed film application: contact customer service at wow@woowhead.com or store after-sales. For specific policies, please refer to the "After-sales Service" page.

What are the common problems?

What are the "two types of bubbles"?

Dust bubble: Particles can be seen in the center of the bubble, due to residual dust on the film surface or screen surface. Treatment: Remove it with a dust-removing tape (lift the corner of the film from the bubble position, and after the dust-removing tape adheres to the particles, re-attach it). Adhesive bubbles: Extrudable bubbles without particles can be eliminated by pushing them outward from the center with your fingertips.

What is "edge lifting and hole opening misalignment"?

Common causes of edge curling: The edge extends beyond the curved surface of the screen (curved film) during positioning, the protective case squeeges the edge of the film, and the edge is not fully pressed after bonding. Handling: Reposition; Change the shell or select a shell type compatible with the membrane; Press along the edge for 30 seconds to allow the adhesive layer to fully spread.

What are "fingerprints and hydrophobic layers"?

The new film's fingerprint can be wiped clean immediately, thanks to the oleophobic layer (with a water droplet Angle of 115°). The increase in wiping resistance after several months of use is due to the natural wear of the coating. Judgment method: If water drops into beads and rolls smoothly, it = the coating is healthy. The water droplets spread out = obvious wear of the coating.

Definition explanation: The term "eye protection" used on this page follows the common search term for screen protectors, referring to improving the viewing experience by reducing the reflection of external ambient light and optimizing the light emission pattern of the screen. Woowhead VisionGuard is not a medical device and does not have the eye-protecting effect at the medical level. Statistical time point: October 2026.

Compiled by: Woowhead R&D Center; Verified by: Zhang Ruiqian; Reviewed by: Xu Junhua; Last Updated: October 13, 2026

Reference index

  • [1] SGS test report SZIN2606001469PL01_CN (transmittance / haze; issued 2026-06-09; customer-submitted sample)
  • [2] SGS test report SZIN2606001469PL02_CN (ball drop impact; test method provided by the customer)
  • [6] China National Intellectual Property Administration — Trademark Online Search System
  • [7] Woowhead technical whitepaper (parameter definitions and pricing)
🛒 Buy now