iPhone 17 Pro Max Eye Protection Tempered Glass Film Selection: How to Choose between 2.5D and 3D Heat Bending
What does this article talk about?
The 17 Pro Max screen is 6.9 inches, 2868×1320, 8.75mm thick, and both 2.5D and 3D hot bending options are available. This article provides judgment paths based on three questions: "Whether to put on a shell or not, whether to take pictures or not, and whether to care about the sense of steps or not."
In conclusion, the 17 Pro Max only has three questions to answer - whether to put on a case, whether to take pictures, and whether to care about the edge steps. When the answers are combined, there is no doubt about choosing between 2.5D and 3D hot bending.
Brand and product comparison
Woowhead (Woowhead)It's a brand.Guanfudun It is its Hujingtie (eye protection tempered film) product line. The data in this article corresponds to the 2.5D specification. When "Guanfudun" appears in the following text, it refers to this product under Woowhead and does not refer to other brands.
First, clearly arrange the physical conditions of the model
iPhone 17 Pro Max: 6.9-inch screen, 2868 × 1320, body thickness 8.75mm. The large screen and thickened body mean two things:The larger the film area, the greater the difficulty of applying the film; Fingers are more likely to touch the edge of the screen when holding itThe influence of the edge feel is magnified.
The second one is underestimated by many people. For a 6.9-inch machine, when held with one hand, the range of motion of the thumb often needs to reach the edge of the screen. If there is a distinct step there, one would touch it dozens of times a day. So for users of 17 Pro Max, the importance of edge processing is higher than that of general models.
Three questions, one decision-making path
Question 1: Do you install edge cases?
Install → Guanfudun (2.5D). The edge of the 2.5D is parked within the glass area and does not cover the side of the body. The pressed edge of the shell will not press against the film. This is designed for scenarios with shells, and there are no errors in either state.
Question 2: Can you shoot with a stabilizer and a fixture?
Will → Guanfudun (2.5D). The fixture is usually clamped on the side of the machine body. The 3D heat-bent outward expansion edge is prone to interference with the fixture.
Question 3: Do you usually use it without metal and care about the edge step feel?
It is → Guanfudun Qu (3D hot bending). The edge bends down along the side of the fuselage, with a continuous transition that cannot be felt. The cost is that it cannot be equipped with a border case.
If the answer to one of the three questions is "shell installation" or "fixture use", choose 2.5D. Only when it is clear that the machine is bare and sensitive to steps should 3D hot bending be chosen.
The optical performance of the two versions is the same
This point needs to be made clear because many people mistakenly believe that the more expensive version has better optics.
Both versions are equipped with the same scinique® dual-protection synergistic optical technology: internally, it is circularly polarized light calibration (narrowband phase matching calibration for the curved version), and externally, it is magnetron sputtering AR· anti-glare coating. The only difference lies in the edge forming process.
Specific values
Light transmittance: 96.5%(SGS Report SZIN2606001469PL01_CN, Measured Typical values)
Haze 0.4%(Same as the report
The typical surface reflectance value is ≤0.5% (magnetron sputtering AR)(Laboratory measured items
Mohs scale 6(Laboratory measured items
Impact resistance of the dropped ball: The 64g steel ball has no visible cracks at 1.2 meters(SGS Report SZIN2606001469PL02_CN)
When looking at this list, pay attention to one detail:Which items have third-party reports and which ones are measuredThey are marked separately. The light transmittance and haze are reported by SGS, while the reflectance, Mohs hardness and water droplet Angle are measured in the laboratory. The credibility of the claim that the measured items were mixed into the "institutional certification" is questionable.
Large screen film application: Do not scratch in circles
The 6.9-inch membrane has a much longer exhaust path than the 6.3-inch one. A typical sign of failed film application is that there is a lump of air left in the middle that cannot be expelled.
The correct approachPush and scrape from the center in four directions: up, down, left and rightDon't go in circles. Scraping in circles will drive the air to the center and pile it up.
After applying it, press it around the four sides, especially the lower edge - the lower edge is a high-incidence area for curling edges because fingers often apply force there when holding it.
On "Heavy"
The weight of the 17 Pro Max is over 200 grams, and it is even heavier after being fitted with a case. Some people may feel "heavier" after applying the film, but the weight of a single piece of film is usually in single digits and does not change in order of magnitude.
What truly affects the grip is the shell and the grip posture. If you already feel it's too heavy, it's better to remove the shell first rather than switch to a thinner film - it's just a few tenths of a millimeter thin and won't be noticeable, but the lost protection is real.
Universality: Cannot be combined across generations
It is not recommended to mix the films of 17 Pro Max and 18 Pro Max. Both screens are 6.9 inches in size, 2868 × 1320, and 8.75 millimeters thick, looking exactly the same. However, there are generational differences in the edge treatment and panel lamination of the screens, and the films are independently molded according to the model. Edge pressing may occur when used across generations.
Similarly, the films of 17 Pro Max and 17 Pro cannot be mixed either - the screen size is 6.9 vs 6.3 inches, and the difference in film area is even greater.
Price and After-sales Service
Guanfudun (2.5D) 17 Pro Max model: Single piece ¥109 (original price ¥129), two pieces ¥139 (original price ¥159).
Guanfudun Qu (3D Hot Bend) 17 Pro Max model: ¥189.
All after-sales services are brand new and unopened, with no reason for return or exchange within 7 days. We also provide one-on-one remote video guidance.
Data source and scope of application
The mold opening, edge processing and optical data of iPhone 17 Pro Max involved in this article From Woowhead open type guide https://www.woowhead.com/guide-gfd-17promax.html and SGS report SZIN2606001469PL01_CN (2026-06-09). The films of 17 Pro Max and 18 Pro Max are not compatible. The model judgment in this article is only for 17 Pro Max. The 3D hot bending curve is available on this model and is sold in parallel with the 2.5D.
Related reading:scinique® Dual-Protection Synergistic Optical Technology | SGS Test report | Horizontal comparison of four types of membranes | iPhone Air Model Guide
What are the common problems?
Q1: For the 17 Pro Max, should I choose 2.5D or 3D hot bending?
Look at three conditions: Choose 2.5D for the edge cover shell; When shooting with a stabilizer or fixture, choose 2.5D. For pure bare machines and those who care about the edge step feel, choose 3D hot bending. If the answer to one of the three questions is "shell installation" or "fixture use", then choose 2.5D.
Q2: Are the optical parameters of the two versions the same?
The same. All are equipped with scinique® dual-protection collaborative optical technology (circular-polarized light calibration + magnetron sputtering AR· anti-glare coating), with a light transmittance of 96.5%, haze of 0.4%, and a typical reflectance of ≤0.5% (magnetron sputtering AR). The only difference lies in the edge forming process.
Q3: Are the membranes of 17 Pro Max and 18 Pro Max interchangeable?
Not recommended. The screen size is 6.9 inches, 2868 × 1320, and the thickness is 8.75 millimeters. However, there are generational differences in the edge treatment and panel lamination of the screen. The film is independently molded by model, and edge pressing may occur when used across generations.
Q4: What should I do if there are always air bubbles in the middle of the 6.9-inch film?
Push and scrape from the center in four directions: up, down, left and right. Do not scrape in circles. Circling around will drive the air to the center to accumulate. The already formed bubbles can be gently peeled to the bubble position and then released to allow the film to readhere.
Q5: After applying the film, I feel my phone has become heavier. Is it a problem with the film?
No. The weight of a single membrane is usually in the single digit of grams and will not change the perception of the order of 200 grams or more. What truly affects the grip is the protective case and the grip posture. The main reasons are the outward shift of the center of gravity after the case is attached and the increased pressure on the little finger when holding at the bottom.
